Voltage drop
How much voltage is lost along a cable. A 12 V system has very little to spare: lose 1.5 V and a 12 V load only sees 10.5 V.
Enter voltage, load, length and cable size.
- Voltage at the load
- Power wasted as heat in the cable
- This cable's safe continuous rating
- Longest run for 3 % drop
- Cable needed for 3 % drop
Wire size
The smallest standard cable that stays inside your voltage-drop limit and carries the current without overheating. It checks both, because either one can be the limit.
Enter voltage, load and length.
| Size | AWG | Drop | Rated | Result |
|---|
Fuse size
A fuse protects the cable, not the appliance. It has to blow before the wire gets hot, but not at normal running current.
Enter voltage and load.
- Absolute minimum (load × factor)
- Fuse type
- Smallest cable this fuse can protect
Watts, amps, volts and ohms
Type any two values and the other two are worked out. Handy for turning a watt rating into the amps it pulls from the battery.
Enter any two values.
Inverter DC draw and cable
An inverter that supplies 1,000 W of 230 V pulls far more than 83 A from a 12 V battery. This gives the real DC current, the fuse and the cable size.
Enter the AC load and cable length.
- DC current, battery at nominal voltage
- DC current, battery nearly flat (design value)
- Peak at surge
- Fuse (close to the battery)
- Cable (each of positive and negative)
- Battery bank size, rule of thumb
Battery runtime
How long a battery will run a load before it hits its safe limit. Lead-acid batteries lose capacity at heavy loads, so this applies a Peukert correction.
Enter the battery size and the load.
- Current drawn from the battery
- Energy you can use
- Effective usable capacity at this load
Charge time
How long a charger, alternator, DC-DC charger or solar will take to fill the battery back up.
Enter the battery size, charger current and charge levels.
- Amp-hours to put back
- Charge rate
- Net current into battery
DC-DC and alternator charging (tow vehicle → caravan)
Charging a caravan, camper or second battery from the vehicle's alternator. A DC-DC charger draws more current from the vehicle than it delivers to the battery, and usually over a long cable, so the input cable is where most installs go wrong.
Enter the charger output and cable lengths.
- Charger output power
- Heat lost in the charger
- Input fuse (at the vehicle battery)
- Input cable (each of + and −)
- Output fuse (at the caravan battery)
- Output cable (each of + and −)
Power budget
List what you run each day to find out how many amp-hours you use, how big the battery should be, and how much solar you need.
Add at least one appliance with watts and hours.
- Energy per day
- Battery draw per day
- Everything on at once
- Battery needed
Solar panel sizing
How many watts of solar replace what you use each day, plus the regulator size. Size for the worst month you'll camp in, usually winter.
Enter your daily energy use and a panel size.
- Solar needed (calculated)
- Regulator, minimum current
- Expected harvest from that array
Solar wiring: series, parallel and cable size
Check that your panel layout is safe for the solar regulator, and what cable to run from the roof. The most common mistake is too many panels in series: on a cold morning the voltage can exceed the regulator's limit and destroy it.
Enter the panel details and your layout.
- Array voltage, coldest (Voc)
- Array working voltage (Vmp)
- Array current (Imp / Isc)
- Expected into the battery
- Panel cable (each + and −)
Battery bank: series and parallel
Wiring in series adds voltage. Wiring in parallel adds capacity (Ah). Use identical batteries of the same age.
Enter battery voltage, capacity and counts.
- Bank voltage
- Bank capacity
- Stored energy
- Number of batteries
Battery percentage from voltage
A rough state-of-charge estimate from a multimeter reading. Only meaningful after the battery has rested with nothing charging or drawing power.
Enter the measured voltage.
Reference tables
Quick look-ups that match the numbers the calculators use.
Cable current ratings (copper, conservative)
| mm² | AWG (same or thicker) | Safe continuous | CCA | Largest fuse | Typical use |
|---|
Ratings assume ordinary automotive PVC or XLPE insulation, bundled in a warm vehicle. They are deliberately conservative: always check the cable maker's data sheet. “CCA” is copper-clad aluminium, which carries roughly 70 % of the current of copper.
Typical 12 V loads
| Load | Watts (approx.) | Amps at 12 V |
|---|
Common questions
Why do you double the cable length?
Current has to flow out to the load and back to the battery. Voltage drops along both the positive and the negative (or chassis return). A 5 m run to a fridge is really 10 m of cable. If you use the chassis as the return, make sure the earth strap is just as thick and the connections are clean and bare metal.
What voltage drop is acceptable?
The usual guide is 3 % (about 0.36 V on 12 V) for anything critical: lights, electronics, fridges, inverters. Up to about 10 % is tolerated for non-critical loads such as a winch motor for short bursts. For charging cables, keep it low (1–3 %) so the battery actually gets the voltage it needs.
Does the fuse go at the battery or at the load?
At the battery (the power source), within about 300 mm of the positive terminal. The fuse protects the cable that runs from it, so a fuse at the far end leaves the whole cable unprotected if it shorts to the bodywork.
Can I use a bigger fuse to stop it blowing?
No. A fuse that keeps blowing is telling you the load is bigger than the circuit. Never fit a fuse rated above what the cable can carry; fix the cause or fit thicker cable.
Is cheap “CCA” cable OK?
It works, but it has around 60 % more resistance than copper for the same size and carries less current, and it corrodes badly at crimps. Select CCA in the calculators to see the difference. For battery, inverter and charging cables, pure copper is worth the money.
What voltage should I design for?
For voltage drop on running circuits, 12 V is the safe assumption; with the engine running it is 13.8–14.4 V. For inverters, design for the low-battery current (around 10.5 V on a 12 V system), since that is when the inverter draws the most.
Series or parallel solar panels?
Series adds voltage, parallel adds current. Series keeps the current low, so the roof cable can be thinner and shading or long runs hurt less in voltage terms, but you must stay under the regulator's maximum PV voltage on a cold morning (panel voltage rises as it gets colder). Parallel is the right choice with a low-voltage PWM regulator or when partial shade is common. Use the Solar wiring calculator to check your layout.
Why isn't my caravan battery charging from the tow vehicle?
- Voltage drop in a long, thin tow-plug cable (use the DC-DC calculator).
- A smart alternator that only charges at ~12.5–13 V, so a basic relay or isolator won't fill the battery. Fit a DC-DC charger.
- The vehicle's charge feed is on an ignition-switched circuit or a fuse that is too small.
- A poor earth/return connection: the return path matters as much as the positive.
Do I need a DC-DC charger or can I wire the battery in directly?
On older vehicles with a fixed 14 V alternator, a direct fused feed through an isolator or relay can work, but the long cable still drops voltage. A DC-DC charger fixes both the smart alternator and long-cable problems, and gives your lithium or AGM battery the correct charge profile. It is the recommended method for caravans and campers today.
What about 24 V trucks?
Everything here works for 24 V: set the system voltage to 24. The same power needs half the current, so cables and fuses can be much smaller. A 24 V system is far kinder to voltage drop.